We offer a wide range of laboratory oil analysis services for Aviation, Marine and Industrial Oils. Our laboratory oil analysis services are including oil sampling, laboratory analysis of physical & chemical properties of suspended contaminants and dirt present in the oil.

These analysis provides complete information of lubricant and machine condition which are further used to reduce the repair & maintenance costs. Moreover, these analysis are conducted by our highly competent laboratory technicians so as to ensure that the laboratory results are accurate & flawless.

We provide full-range of oil analysis for Marine, Aviation & Industrial Oils:

• Engine Oil Analysis
• Petrol Engine Oil Analysis
• Diesel Engine Oil Analysis
• Diesel Mixed with Kerosene Analysis
• Marine Engine Oil Analysis – Vessel, Ship, Boat, Yacht, Diesel Engine Oil Analysis
• Gas Engine Oil Analysis
• Hydraulic / Transmission Oil Analysis
• Turbine Oil Analysis
• Gear / Gearbox Oil Analysis
• Differential / Final Drive & Transmission Oil Analysis
• Refrigeration Compressor Oil Analysis
• Air Compressor Oil Analysis
• Grease Analysis
• Engine Coolant Analysis
• Thermal Oil Analysis
• Heat Transfer Oil Analysis
• Transformer Oil Analysis
• Bearing Oil Analysis
• Diesel Oil Analysis
• Industrial Oil Analysis
• Aircraft Fuel Analysis, Jet Fuel Analysis, Aviation Fuel Analysis, Skydrol Analysis, Phosphate Ester Analysis, Jet A1 Fuel Analysis

Below are some of our test that we provide. For other test that is not listed here, please contact us:

• Fluid Properties Analysis:
  • Viscosity @ 40°C
  • Viscosity @ 100°C
  • Viscosity Index,VI
  • Base Number,TBN
  • Soot
  • Glycol
  • Nitration
  • Sulphation
  • Oxidation
• Additive/Contaminants Analysis:
  • Mg(Magnesium)
  • Mo(Molybdenum)
  • B (Boron)
  • Ca (Calcium)
  • Zn (Zinc)
  • P (Phosphorus)
• Fluid Contamination Analysis:
  • Moisture by FTIR
  • Moisture by Karl Fischer
  • ISO/NAS (Particle Cleanliness)
  • Acidity, TAN
  • Fuel Dilution
• Wear Debris Analysis:
  • PQ Index
  • Wear Metals/Contaminants Analysis
  • Al (Aluminium)
  • Cr (Chromium)
  • Cu (Copper)
  • Fe (Iron)
  • Pb (Lead)
  • Sn (Tin)
  • Si (Silicon)
  • Na (Sodium)
  • K (Potassium)
  • Ni (Nickel)
• For Engine Coolant:
  • Nitrite, Chloride, pH, TDS, Res.Alk, Conductivity and Glycol %

Below are some of our test method that we have. For other test that is not listed here, please contact us:

• ASTM D130 – Copper Corrosion from Petroleum Products
• ASTM D1401 – Water Demulsibility
• ASTM D1500 – Visual Colour & Appearance
• ASTM D1524 – Visual Examination @ Lab
• ASTM D1533 – Moisture Content
• ASTM D1533 – Moisture Content @ 20 Degree Celsius
• ASTM D1831 – Roll Stability (mm/10)
• ASTM D2270 – Viscosity Index
• ASTM D2272 – RPVOT
• ASTM D240 Gross Calorific Value
• ASTM D2500 – Cloud Point
• ASTM D2668 – Dissolved Gas Analysis (DGA)
• ASTM D2668 – DBPC Content (Oxidation Inhibitor)
• ASTM D2709 – Water & Sediment
• ASTM D2783 – Load Wear Index Oil
• ASTM D2783 – Weld Point – Oil
• ASTM D2887 – GC-MS for Carbon Range
• ASTM D2896 – Total Base Number, TBN, BN, Alkaline Reserve
• ASTM D3328- Fingerprint Analysis by GC-FID
• ASTM D3427 – Air Release
• ASTM D4052 – Density / Specific Gravity
• ASTM D4055 – Pentane Insoluble by Membrane Filtration
• ASTM D4294 – Sulphur by XRF
• ASTM D445 – Viscosity @ 40 Degree Celsius
• ASTM D4530 – Micro Carbon Residue
• ASTM D4629 – Nitrogen
• ASTM D473 – Sediment by Extraction
• ASTM D482 – Ash
• ASTM D4898 – Gravimetric Analysis
• ASTM D4929 – Chloride Content
• ASTM D4951 – Wear Metals, Contaminants & Additives
• ASTM D5185 – Metal in Oil Analysis (Cu, Fe, AI)
• ASTM D5185 / ASTM D4951 – Additive Elements, Wear Metals & Contaminants by ICP
• ASTM D5293 – CCS Viscosity @ -35 Degree Celsius
• ASTM D5293 – CCS Viscosity @ -15°C (cP)
• ASTM D5800 B – Evaporation Loss
• ASTM D5800 B – Method B NOACK Volatility
• ASTM D5837 – Furan Analysis with Estimated DP
• ASTM D6079 – Lubricity
• ASTM D611- Aniline Point
• ASTM D613 – Cetane Number
• ASTM D6304 – Water by Karl Fischer, ppm
• ASTM D6304-A – Water, ppm
• ASTM D6304-C – Water (%)
• ASTM D6371 – Cold Filter Plugging Point
• ASTM D6375 – NOACK Volatility (TGA)
• ASTM D655-A – Rust Prevention – A
• ASTM D664 – Total Acid Number, TAN
• ASTM D6971- RULER
• ASTM D7042 – Kinematic Viscosity @ 40 Degree Celsius
• ASTM D7042 – Kinematic Viscosity @ 100 Degree Celsius
• ASTM D7042 – Kinematic Viscosity @ 30 Degree Celsius
• ASTM D7843 – Membrane Patch Colorimetry (MPC)
• ASTM D86 – Distillation of Petrol Products
• ASTM D891-B – Density (Specific Gravity)
• ASTM D874 – Sulphated Ash
• ASTM D892 – Foaming
• ASTM D92 – Flash Point, COC
• ASTM D93 – Flash Point (PMCC)
• ASTM D9334 – Flash Point
• ASTM D943 – Oxidation Characteristics
• ASTM D95 – Flash Point
• ASTM D95 – Water in Petroleum Products by Distillation, %
• ASTM D97 – Pour Point of Petroleum Products
• ASTM D971 – Interfacial Tension (IFT)
• ASTM D974 – Total Acid Number
• ASTM D976 – Cetane Index
• Copper Corrosion (3 Hours @ 100C)
• FTIR / ASTM D6304 – Water Content Analysis
• FTIR – Oxidation
• FTIR – Soot
• FTIR – Sulphation
• FTIR – Nitration
• IEC 60156 – Dielectric Breakdown Voltage (BDV)
• IEC 60247 – Dielectric Dissipation Factor @ 90 Degree Celcius
• IEC 60247 – Resistivity
• IEC 60422 ANNEX C – Sedimentation
• IEC 60422 ANNEX C – Sludge
• IEC 62535 – Corrosive Sulphur
• NAS 1638 – Particle Count
• IP 385 – Jet A1 Fuel Analysis
• ISO 4406 – Particle Count
• Particle Count (DILUTED) > 4um, >6um, >14um
• IP239 – MWSD (1 h, 40 kg)
• APHA 3125 B FRESH WATER ANALYSIS
• APHA 9260 J AIRCOND WATER ANALYSIS

Aircraft Fuel / Jet Fuel Analysis Services

We provide oil analysis services for Aircraft Fuel Analysis, Jet Fuel Analysis, Aviation Fuel Analysis, Skydrol Analysis, Phosphate Ester Analysis, Jet A1 Fuel Analysis.

Below are some of our test that we provide for Aircraft / Jet Fuel Analysis. For other test that is not listed here, please contact us:

• Kathon Presence Detection Analysis
• IP385 Determination of the Viable Aerobic Microbial Content
• Particle Extraction and Analysis by Scanning Electron Microscope (SEM)
• Chlorine Content
• Specific Gravity
• Conductivity
• Particle Count
• Elemental Analysis by ICP
• Viscosity at 40°C
• Total Acid Number (TAN)
• Water Content
• Immunoassay testing

Transformer Oil Analysis Services

Oil samples from transformer are drawn in order to test the oil properties & to determine the quality of the oil such as dissolved gases (DGA), dielectric breakdown voltage (BDV), moisture content, Furan, Acidity, Interface Tension,  Dielectric Dissipation Factor (DDF), Specific Gravity, Metal in Oil, Sedimentation, Oxidation Inhibitor (DBPC Content), etc.

Below are some of our test that we provide for Transformer Oil Analysis. For other test that is not listed here, please contact us:

• Dissolved Gas Analysis (DGA) ASTM D3612
• Moisture Content ASTM D1533
• Acidity ASTM D974
• Interfacial Tension (IFT) ASTM D971
• Dielectric Breakdown Voltage (DBV) IEC 60156
• Colour & Visual ASTM D1500
• Dielectric Dissipation Factor (DDF) IEC 60247
• Specific Gravity In-House
• Metal In Oil (Cu,Fe,Al) ASTM D5185
• Sedimentation IEC 60422 Annex C
• Oxidation Inhibitor (DBPC Content) ASTM D2668
• Furan Analysis (with estimated DP) ASTM D5837
• Corrosive Sulphur IEC 62535
• Resistivity IEC 60247
• Dielectric Dissipation Factor @90C IEC 60247
• Sludge IEC 60422 Annex C
• Flash Point ASTM D9334